Contents:

• Disclaimer For Communications Application Configurations For Intel Faxmodems
• Attachmate/Crosstalk Communicator Tech Support
• Configuring DCA'S Off-The-Shelf Crosstalk Communicator
• Crosstalk Communicator Flow Control Defaults To XON/XOFF
• Crosstalk Communicator - Pulse Dialing
• Crosstalk XVI Configuration For Intel Faxmodems
• Crosstalk Mark 4: Compatible With Intel® Modems & Intel® Faxmodems
• Crosstalk For Windows* V1.1

Intel provides suggested communications application configurations solely as a service to Intel faxmodem customers. Intel assumes no responsibility for errors or omissions in this information. Nor does Intel make any commitment to update this information. If you have questions or problems while configuring a communications application, consult the manual or the manufacturer of the application

If you have questions about Crosstalk Communicator you'll want to contact Attachmate Corporation.

The Intel version of Crosstalk Communicator contains setup selections for all Intel modems. The off-the-shelf version from DCA must be configured specially for your modem. The first table shows the settings that are different from modem to modem. The second table shows settings that are the same for all Intel Faxmodems.

Table of Suggested Intel Faxmodem Settings

Table of Common Intel Faxmodem Settings

Intel recommends resetting the default flow control option to RTS/CTS (Request to Send/Clear to Send) when using faster data transmission rates. To change the default flow control setting:

1. Start Crosstalk Communicator
   
   
2. Highlight "Normal"
   
   
3. Press Alt-D
   
   
4. Highlight "Flow"
   
   
5. Use the space bar to toggle to RTS/CTS
   
   
6. Press Ctrl-Enter to accept the change

NOTE: The new flow control default will apply to future entries only. Entries made before the default was changed will remain at their original setting. If you wish to reset the flow control option for these earlier entries, highlight the items you wish to change then follow the steps listed above.

If you need to change from Tone dialing to Pulse dialing, here's what you need to do:

1. Press ALT-S to enter Setup
2. Press PageDown to view the second Setup screen
3. Set the Dial Modifier to ATDP

Here is the suggested Crosstalk XVI configuration for Intel Faxmodems.

• Start up Crosstalk XVI. At the Status Screen, press <ENTER>to get into command mode:
  
  
• Set the correct serial port.

  - Type: PO x <ENTER> (where "x" is the serial port that your Intel Faxmodem is using).

• Enter the appropriate command to set the correct baud rate for your faxmodem:

* Set the flow control for your modem

• To view the Miscellaneous Parameters screen, type: LIT <ENTER>
  
  
• To turn Software Flow Control OFF, type: FLOW- <ENTER>
  
  
• To turn Software Flow Control ON, type: <Ctrl-S>
  
  
• To turn on Hardware Flow Control, type : HA ON <ENTER>
  
  
• To turn off Hardware Flow Control, type: HA OFF <ENTER>
  
  

  * Go into terminal mode and issue the appropriate command for your modem.

  - Type GO LO <ENTER>
  
  - Enter the correct command for your modem.

Crosstalk Mark 4 is compatible with Intel Modems, Intel Faxmodems & the SatisFAXtion Modem/100.

Here's how to configure Crosstalk Mark 4.

With AUTOEXEM enabled, you will see a menu after starting Crosstalk Mark 4. Press <ESCAPE>to get to the command prompt. With AUTOEXEM disabled, you will immediately see the command prompt.

* Set the serial port. Type: PORT <ENTER>

Highlight the port on which you installed your modem and press <ENTER>.

* Select the correct baud rate for your modem. If you use a High Speed V.42bis modem (1), select the highest speed your modem supports. Type: SPEED <ENTER>

* Select flow control for your modem. Type: FLOW <ENTER>

* Select "modem init" string in Crosstalk Mark 4.

This applies to:

Modems and Fax Boards