|
Contents:
Quick Link II: Compatible With Intel Modems
This modem is compatible with Intel modems. Here's how to configure Quick Link II. For more information contact smith Micro at: 714-362-5810 (number valid as of 9/29/92).
- Run Quick Link
- Select "Modem Setup" from the "Setup"/"Modem Setup" menu
- Set the "Init string" to AT&F&C1&D2
- Set "Dial prefix" to ATDT
- Set "Hangup string" to ATH
- Set "Modem port" to the phone icon
- Select "Terminal options" from the "Setup"/"Terminal Options"menu.
|
XON/XOFF |
XTS/RTS |
Max. |
| flow ctl |
flow Ctl |
Baud Rate |
| 14.4EX |
OFF |
ON |
57600 |
| 9600EX |
OFF |
ON |
38400 |
| 2400EX MNP |
OFF |
ON |
4800 |
| 2400EX |
ON |
OFF |
2400 |
Smartcom III: Compatible With Intel ModemS
This program is compatible with all Intel modems. Smartcom III is designed for use with Hayes modems and any deviation can cause problems. So before using Smartcom III with any Intel MNP modem (all SatisFAXtion Modems, 14.4EX, and 9600EX included), you must configure them identically to the Hayes. Use the "Terminal emulation" option in Intel's TESTCOM program to send the command AT\J1\N0\Q0\V0&W to the modem.
Vainfo 3.21: Semi-Compatible With 14.4Ex
VAINFO 3.21 is provided by the US Department of Veteran's Affairs for downloading listings of homes for sale by the Veterans Administration.
Tested by The Vendor
VAINFO version 3.21 is compatible with the 14.4EX modem. However, earlier versions of VAINFO are not compatible with the 14.4EX.
Configuring Qmodem For Intel Modems &Amp; Faxmodems
Intel's lab tested QMODEM (versions 3.1 & 5.x) with the SatisFAXtion Modem/350 & Modem/100 board, and it is compatible.
The first time you run Qmodem it automatically takes you to the "Setup Menu". After the first time, use <ALT-N>to call up the "Setup Menu".
- Press 'C' to select "Communications Parameters"
- Press 'A' to select "Default baud rate"
- Highlight the baud rate for your modem then press <ENTER>
| If you have: |
Choose: |
| Intel 144/144e, 144/144i, |
|
| 96/96e, 96/96i |
|
SatisFAXtion Modem/350, 300
|
| Intel 14.4EX, 9600EX |
38400 (or 57600 if supported |
| Intel 24v/96e, 24v/96i, |
|
| Faxmodem, 2400 V.42bis |
|
| Modem, Upgraded SatisFAXtion |
|
| Classic |
9600 |
| SatisFAXtion Classic, |
2400B |
| MNP Modems |
4800 |
| Intel 24/96i Faxmodems, Intel |
|
| non-MNP 2400bps modems, |
|
| SatisFAXtion Modem/100 |
2400 |
Press 'J' to select "Serial Port"
Type the number of the COM port of your modem and press <ENTER>
Press <ESCAPE>
Press 'M' to select "Modem Commands"
Press 'I' to select "Initialization Command"
Type 'ATZ^M' then press <ENTER>.
Press <ESCAPE>
Note:
QMODEM Comes with COM1 and COM2 defined, but COM3 and COM4 are undefined. If you installed your modem on COM3 or COM4, use the following commands to define the address and IRQ for COM3 or COM4. If you installed your modem on COM1 or COM2, skip over this section to the next.
If you installed your modem on COM3 or COM4, press 'P' to select "Port Addresses" then follow these instructions:
Highlight the "Base" address of your modem's COM port then <ENTER>
Type '0', your modem's 3 digit address (3E8 for COM3 or 2E8 for COM4), then press <ENTER>
Highlight the "IRQ" of your modem's COM port then <ENTER>
Type your modem's IRQ number then <ENTER>
Press <ESCAPE>twice
Press H to select "Host" options menu.
Press I to select "Init Command".
Type ATZS0=1^M (delete any extra characters) then <ENTER>.
Note:
For Intel faxmodems, the number following "S0=" should match the number of rings you specified in the SatisFAXtion SETUP program.
Press A to select "Answer Command" then delete ATA^M and leave the field blank.
Press <ESCAPE>
Press M to select "Modems"
Press T to select "Toggles"
Set the following option for your modem:
SatisFAXtion Modems
|
100 |
Classic |
Upgraded Classic, 300,350 |
| [XON/XOFF] Flow ctrl. |
ON |
OFF |
OFF |
| CTS/RTS signal |
OFF |
ON |
ON |
| RTS When writing |
OFF |
OFF |
OFF |
| Fifo during shell |
|
|
|
| Lock DTE baud rate |
ON |
ON |
ON |
| High speed Xmit |
ON |
ON |
ON |
| 16550 UART enable |
[*] |
OFF |
OFF |
| INIT ignores CD |
ON |
ON |
ON |
Intel Faxmodems
|
144/144, 96/96 |
24v/96 |
24/96i |
| [XON/XOFF] Flow ctrl. |
OFF |
OFF |
OFF |
| CTS/RTS signal |
ON |
ON |
OFF |
| RTS When writing |
OFF |
OFF |
OFF |
| Fifo during shell |
|
|
|
| Lock DTE baud rate |
ON |
ON |
ON |
| High speed Xmit |
ON |
ON |
ON |
| 16550 UART enable |
ON (if present) |
OFF |
OFF |
| INIT ignores CD |
ON |
ON |
ON |
Intel Modems
|
non-MNP |
2400 MNP |
14.4EX, 9600EX,2400V.42bis |
| [XON/XOFF] Flow ctrl. |
ON |
OFF |
OFF |
| CTS/RTS signal |
OFF |
ON |
ON |
| RTS When writing |
OFF |
OFF |
OFF |
| Fifo during shell |
|
|
|
| Lock DTE baud rate |
ON |
ON |
ON |
| High speed Xmit |
ON |
ON |
ON |
| 16550 UART enable |
[*] |
|
|
| INIT ignores CD |
ON |
ON |
ON |
Note:
* = ON if your serial port has one, otherwise OFF.
press <ESCAPE>twice
- Press E to select "Exit"
Press S to select "Save changes"
- Now configure your modem.
In terminal mode, enter the correct command for your modem:
Upgraded SatisFAXtion Classic,
| SatisFAXtion Modem/300, 350 |
AT&F&W <ENTER> |
| SatisFAXtion Classic |
AT&F\N3\Q3\J0&W <ENTER> |
| Modem/100 |
AT&F&C1&D2&W <ENTER> |
| Intel Faxmodems |
AT&F&W <ENTER> |
| 14.4EX, 9600EX, 2400 V.42bis modems |
AT&F&W <ENTER> |
| 2400B MNP modems |
AT&F\N3\Q3\J0&W <ENTER> |
| Intel non-MNP modems |
AT&F&C1&D2&W <ENTER> |
Relay Gold 1.0: Compatible With Modem/100
Tested by Intel
Intel's lab tested Relay Gold version 1.0 with the Modem/100, and it is compatible.
Smartcom Ii V3.0: Semi-Compatible With Modem/350 And Classic
Before using Smartcom II version 3.0 with the SatisFAXtion modem, you must remove the fax program from memory. If you don't, your system will lockup when you load Smartcom. Enter the command CASMGR /U.
See "Configuring Smartcom II for SatisFAXtion Modems" for configuration information.
Configuring Smartcom Ii For Satisfaxtion Modems
Smartcom II version 3.0 works fine with the Modem/100. For all other SatisFAXtion modems, you must disable all error detection and data compression features before using Smartcom.
Use the "Terminal emulation" option in Intel's TESTCOM program to send this command to the SatisFAXtion modem: AT\J1\N0\Q0\V0&W
Special notes about Smartcom II Version 3.0:
- Version 3.0A should be compatible with all SatisFAXtion modems.
- Version 3.0B is unknown.
- Version 3.0C is incompatible because it checks for a Hayes ROM in the modem. If the modem ROM's checksum doesn't exactly match Hayes, the program doesn't work with that modem.
Smartcom Ii: Compatible With Modem/100
Tested by Intel
Intel's lab tested this software (version 3.0a) with the SatisFAXtion/100 board, and it is compatible.
Before using Smartcom II version 3.0 with the SatisFAXtion or Connection CoProcessor (CCP) modem, you must remove the fax program from memory. If you don't, your system will lockup when you load Smartcom. For Upgraded SatisFAXtion Classic and SatisFAXtion Modem/350, enter CASMGR /U. For SatisFAXtion/100 enter CASMODEM /U. For CCP, enter XCAM.
WINCIM 1.0
Tested by Intel
Intel was able to connect to CompuServe using
WinCIM 1.0 and download several files ranging in size from 1K to 567K. Intel used DOWNLOAD.400 version 3.10 and CASMGR 1.42 with the Modem/350.
Suggestions for Better Performance:
- Optimize conventional memory with your Expanded Memory Manager (for example, QEMM, 386MAX, EMM386) for the largest block of conventional memory your system setup will allow.
- Use the Ports section of the Windows Control Panel to set up the COM port:
- Select the highest speed supported by your modem.
- Set Flow control to "Hardware".
- Verify that you have Intel's latest SatisFAXtion software.
- 4. Select [Intel SatisFAXtion] setting for your modem.
- Modify the setting to: [Intel SatisFAXtion Modem/350] and enter the init string: AT &F \N4 E0 L0 ^M This setting works fine at 9600/14400/19200 bps.
If you have any further troubles, contact the WinCIM support forum on CompuServe. The forum is called WCIMSUPPORT.
Vainfo 3.21: Semi-Compatible With Modem/100
VAINFO 3.21 is provided by the US Department of Veteran's Affairs for downloading listings of homes for sale by the Veterans Administration.
Tested by Intel
Intel tested VAINFO 3.21 with the SatisFAXtion Modem/100, and they are compatible.
Vainfo 3.21: Semi-Compatible With Satisfaxtion Modem/350
VAINFO 3.21 is provided by the US Department of Veteran's Affairs for downloading listings of homes for sale by the Veterans Administration.
Tested by The Vendor
VAINFO version 3.21 is compatible with the SatisFAXtion Modem/350. However, earlier versions of VAINFO are not compatible with the SatisFAXtion Modem/350.
This applies to:
| 
