Support & Downloads

Browse By Product



Search
Support & Downloads
Networking Connectivity
Elite Gateway*
Dial Plan Example Using Web Interface

This document describes how to use a web browser to build a sample scenario dial plan in the Elite Gateway*.

Suggested steps to set up a dial plan at the web browser setting:

  1. Diagram the scenario to have a VoIP call application
  2. Local gateway: IP setup
  3. Local gateway: local telephone number setup
  4. Local gateway: remote gateway IP and remote telephone number setup
Diagram the scenario to have a VoIP call application

Note: If you don't have PBX on hand, please ignore GW A Port 5 setting.

Diagram the scenario to have a VoIP call application - diagram

Scenario description:

Gateway A is configured as follows:

  1. Gateway A IP: 192.168.0.20, mask IP: 255.255.255.0, gateway IP 0.0.0.0 (virtual IP).
  2. Slot A plugs FXS module and slot B plugs FXO module.
  3. Port 1 of FXS in slot A has a telephone set connected, its phone number is 200.
  4. Port 3 of FXS in slot A has a telephone set connected, its phone number is 201.
  5. Port 1 of FXO in slot B is connected to PBX. There are two telephone sets connected by PBX, their phone numbers are 800 and 810.
Gateway B is configured as follows:
  1. Gateway B IP: 192.168.0.55, mask IP: 255.255.255.0, gateway IP 0.0.0.0 (virtual IP).
  2. Slot A plugs FXS module and slot B is empty.
  3. Port 1 of FXS in slot A has a telephone set connected, its phone number is 550.
  4. Port 2 of FXS in slot A has a telephone set connected, its phone number is 551.
Gateway A Configuration

Local gateway IP setup for gateway A

  1. Select Main Menu\ Configure System Settings\ Elite Gateway IP Settings from Main Menu.
  2. Key-in IP Address: 192.168.0.20, Subnet Mask: 255.255.255.0 and Default IP Gateway Address: 0.0.0.0 in the related fields.
  3. Click "Save The Change" button.

IP Address Settings - diagram

Add telephone address to hunt group mapping table of phone number 200 into dial plan

Gateway A's local telephone number is 200. 200 is located at Port 1 of the FXS module in slot A.

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add telephone" from Main Menu.

    Add Telephone Numbers screen

  2. Click "Complete" and the screen will show "Telephone Number Added 200 OK" table. Telephone number 200 is added in the gateway dial plan.
Add hunt group to destination ID mapping table of phone number 200 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Hunt Group" from the Main Menu.

    Add Hunt Group IDs screen

  2. Click the "Complete" button and the screen will show the "List All Hunt Group IDs Result:" table.
Add destination ID to destination IP mapping table of phone number 200 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Local_Destination_Channel" from Main Menu.

    Add Local Destination ID screen

  2. Click the "Complete" button and the screen will show "Add Destination ID Result:" table. The Destination ID 1 is bound to local channel 0. Channel Number can have values from 0 to (number of ports -1).
Add telephone address to hunt group mapping table of phone number 201 into dial plan

Gateway A's telephone number is 201. 201 is located on Port 3 of the FXS module in slot A.

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add telephone" from Main Menu.

    Add Telephone Numbers screen

  2. Click the "Complete" button and the screen will show the "Telephone Number Added 201 OK" table. Telephone number 201 is added to the gateway dial plan.
Add hunt group to destination ID mapping table of phone number 201 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Hunt Group" from Main Menu.

    Add Hunt Group IDs screen

  2. Click the "Complete" button and the screen will show the "List All Hunt Group IDs Result:" table.
Add destination ID to destination IP mapping table of phone number 201 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Local_Destination_Channel" from Main Menu.

    Add Local Destination ID screen

  2. Click the "Complete" button and the screen will show the "Add Destination ID Result:" table.
    The Destination ID 3 is bound to local channel 2.
Add telephone address to hunt group mapping of phone number 800 and 810 into dial plan

Gateway A's telephone numbers 800 and 810 are located on Port 1 of FXO in slot B. Because slot B is the second slide-in module of this gateway, you can define the hunt group number by beginning at number 5 in this dial plan setting.

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Telephone" from Main Menu.
  2. Key-in 800 and click "More Entries for the Same Hunt Group" button, and the key-in 810.
  3. Click "Complete" and the screen will show the "Telephone Number Added 800 and 810 OK" table. Telephone numbers 800 and 810 are stored in gateway dial plan.

Add Telephone Numbers screen

Add hunt group to destination ID mapping table of phone number 800 and 810 into dial plan

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Hunt Group" from Main Menu.

    Add Hunt Group IDs screen

  2. Click "Complete" and the screen will show the "List All Hunt Group IDs Result:" table.
Add destination ID to destination IP mapping of phone number 800 and 810 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Local_Destination_Channel" from Main Menu.

    Add Local Destination ID screen

  2. Click the "Complete" button and the screen will show the "Add Destination ID Result:" table.
    The Destination ID 5 is bound to local channel 4.
Add telephone address to hunt group mapping of phone number 550 and 551 into dial plan

Gateway A's remote telephone numbers are 550 and 551. Because 550 and 551 are located in a remote gateway, the hunt group number can be defined beginning at number 11 in this dial plan setting.

  1. Select "Main Menu\Dial Plan\Phone/Hunt Group/Destination Settings\Phone/Hunt Group/Dest. Setting Menu" from Main Menu.

    Add Telephone Numbers screen

  2. Key-in 550 and click "More Entries for The Same Hunt Group" button, and then key-in 551.
  3. Click "Complete" and the screen will show the "Telephone Number Added 550 and 551 OK" table. Telephone number 550 and 551 are stored in the gateway dial plan.
Add hunt group to destination ID mapping table of phone number 550 and 551 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Hunt Group" from Main Menu.

    Add Hunt Group IDs screen

  2. Click "Complete" and the screen will show the "List All Hunt Group IDs Result:" table.
Add destination ID to destination IP mapping of phone number 550 and 551 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Remote_Destination_IP" from Main Menu.

    Add Remote Destination ID screen

  2. Click "Complete" and the screen will show "Add Destination ID Result: The Destination ID 11 is bound to IP address 192.168.0.55 for H.323 VoIP application."
Back To Dial-Plan Menu
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ List Telephone" and the following screen should appear:

    List All Phone Numbers Result screen

  2. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ List Hunt Group" and the following screen should appear:

    List All Hunt Group IDs Result screen

  3. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu" from Main Menu and select List Remote_Destination_IP or Local_Destination_Channel, and the following screen should appear:

    List All Destination IDs Result screen

Save configuration to flash
  1. Select Main Menu\Dial Plan\Store Settings To Flash. The above setting will be stored to flash memory.
You have now finished the gateway A VoIP call application setting.

Gateway B Configuration

Local gateway IP setup for gateway B

  1. Select Main Menu\ Configure System Settings\ Elite Gateway IP Settings from Main Menu.
  2. Key-in IP Address: 192.168.0.50, Subnet Mask: 255.255.255.0 and Default IP Gateway Address: 0.0.0.0 in the related fields.
  3. Click "Save the Change" button.

IP Address Settings screen

Add telephone address to hunt group mapping table of phone number 500 into dial plan

Gateway B's local telephone number is 550. 550 is located on Port 1 of the FXS module in slot A.

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Telephone" from Main Menu.

    Add Telephone Numbers screen

  2. Click the "Complete" button and screen will show the "Telephone Number Added 550 OK" table. Telephone number 550 is stored in gateway dial plan.
Add hunt group to destination ID mapping table of phone number 550 into dial plan

Add Hunt Group IDs screen

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Hunt Group" from Main Menu.
  2. Click "Complete" and the screen will show the "List All Hunt Group IDs Result:" table.
Add destination ID to destination IP mapping table of phone number 550 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Local_Destination_Channel" from Main Menu.

    Add Local Destination ID screen

  2. Click "Complete" and the screen will show the "Add Destination ID Result:" table
    The Destination ID 1 is bound to local channel 0.
Add telephone address to hunt group mapping table of phone number 551 into dial plan

Gateway B's telephone number is 551. 551 is located on Port 2 of the FXS module in slot A.

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings \ Phone/Hunt Group/Dest. Setting Menu\ Add Telephone" from Main Menu.
  2. Click "Complete" and the screen will show the "Telephone Number Added 551 OK" table. Telephone number 551 is stored in gateway dial plan.

Add Telephone Numbers screen

Add hunt group to destination ID mapping table of phone number 551 into dial plan

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Hunt Group" from Main Menu.

    Add Hunt Group IDs screen

  2. Click "Complete" and the screen will show the "List All Hunt Group IDs Result:" table.
Add destination ID to destination IP mapping table of phone number 551 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Local_Destination_Channel" from Main Menu.
  2. Click "Complete" and the screen will show the "Add Destination ID Result:" table
    The Destination ID 2 is bound to local channel 1.

Add Local Destination ID screen

Add telephone address to hunt group mapping table of phone number 200 and 201 and 800 and 810 into dial plan

Gateway B's remote telephone numbers are 200, 201, 800, and 810 settings. Because 200, 201, 800, and 810 are located in the remote gateway, you can define the hunt group number beginning at number 11 in this dial plan setting.

  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Telephone" from Main Menu.

    Add Telephone Numbers screen

  2. Key-in 200 and click "More Entries for The Same Hunt Group" button. Then key-in 201, and click "More Entries for The Same Hunt Group" button and key-in 800, and click "More Entries for The Same Hunt Group" button and key-in 810.
  3. Click "Complete" and the screen will show the "Telephone Number Added 200 and 201 and 800 and 810 OK" table. Telephone number 200 and 201 and 800 and 810 are stored in gateway dial plan.
Add hunt group to destination ID mapping table of phone number 200, 201, 800, and 810 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Hunt Group" from Main Menu.

    Add Hunt Group IDs screen

  2. Click the "Complete" button and the screen will show the "List All Hunt Group IDs Result:" table.
Add destination ID to destination IP mapping table of phone number 200, 201, 800, and 810 into dial plan
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ Add Remote_Destination_IP" from Main Menu.

    Add Remote Destination ID screen

  2. Click "Complete" and the screen will show the "Add Destination ID Result: The Destination ID 11 is bound to IP address 192.168.0.20 for H.323 VoIP application."
Back To Dial-Plan Menu
  1. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ List Telephone" from Main Menu, and the following screen should appear:

    List All Phone Numbers Result screen

  2. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu\ List Hunt Group" from Main Menu, and the following screen should appear:

    List All Hunt Group IDs screen

  3. Select "Main Menu\ Dial Plan\ Phone/Hunt Group/Destination Settings\ Phone/Hunt Group/Dest. Setting Menu" from Main Menu and select List Remote_Destination_IP or Local_Destination_Channel, and the following screen should appear:

    List All Destination IDs Result screen

Save configuration to flash
  1. Select Main Menu\Dial Plan\Store Settings To Flash. The above setting will be stored to flash memory.
You have now finished the gateway B VoIP call application setting. VoIP calls between gateway A and gateway B can now be completed.

This applies to:
Elite Gateway*

End of Interactive Support Announcement
These products are no longer being manufactured by Intel. Additionally, Intel no longer provides interactive support for these products via telephone or e-mail, nor will Intel provide any future software updates to support new operating systems or improve compatibility with third party devices and software products.

THESE DOCUMENTS ARE PROVIDED FOR HISTORICAL REFERENCE PURPOSES ONLY AND ARE SUBJECT TO THE TERMS SET FORTH IN THE "LEGAL INFORMATION" LINK BELOW.For information on currently available Intel products, please see www.intel.com and/or developer.intel.com
Solution ID: CS-008519
Date Created: 18-Jan-2004
Last Modified: 21-Jan-2004
Back to Top